Machine Health Ultra Low | Augury
Complete the detection picture with Augury’s ultrasonic and vibration sensing capabilities for critical low-RPM machines.
Advanced AI diagnostics for clear, prescriptive insights and root causes — down to 1 RPM
Robust ultrasonic sensors for continuous monitoring — up to 100kHz
No more guesswork and manual inspections — fully connect, monitor, and protect your slowest critical assets
Part of Augury’s Machine Health 360, expanding coverage and control to more assets and more environments
| Bearing lubrication | Bearing wear | Axial unbalance |
| Damaged rotor bars | Electrical faults | Electrical discharge via bearings |
| Gear friction | Structural mechanical looseness | Loose rotor bars |
| Loose stator windings | Misalignment | Worn/Eccentric Motor Sheave |
| Rotor mesh abnormality | Rotor eccentricity | Radial unbalance |
| Rubbing/Friction | Shaft eccentricity (Motor) | Significant change in vibrations |
| Stator eccentricity | Impacting | Kiln refractory looseness |
*Full diagnostic fault coverage is available through a combination of Halo R4000 motor sensors and Halo U2000 low RPM sensors.
The new Halo U2000 sensor delivers full-spectrum ultrasound data to effectively monitor your low RPM critical machinery.
Sensing
Sensor Element/Structure: PZT Ceramic/Shear Mode
Dynamic Range: ± 80g, peak; *Vsource ≥ 22V, 12V bias
Frequency Response: ± 3dB (0.5Hz – 22 kHz)
Frequency Response: ± 10% (1 Hz – 16 kHz)
Peak Sensitivity: ± 21dB ± 2 dB
Electrical
Sensitivity (± 10%): 100 mV/g
Spectral Noise @ 10 Hz: 30 μg/√Hz
Spectral Noise @ 100 Hz: 4 μg/√Hz
Spectral Noise @ 1000 Hz: 2 μg/√Hz
Case Isolation: > 108 ohm
Environmental/Physical
Operating Temperature Range: -50°C to +121°C (-58°F to +250°F)
Maximum Shock Protection: 10,000g, peak
Electromagnetic Sensitivity: CE
Sealing: Welded/Hermetic
Submersible Depth: 200 ft. (60 m)
SIL Rating: SIL 2
Case Material: 316L Stainless Steel
Mounting Thread: 1/4-28 UNF
Connector (non-integral): 2 Pin mini-MIL, J series connector
Resonant Frequency: 2,520,000 CPM ± 12,000 CPM (42 kHz±2kHz)
Calibration Certificate: CA10
The new Halo Hub 1.0 is designed for simultaneous analog signal acquisition from Augury’s proprietary wired sensors. It is a fully integrated unit that combines 24-bit analog-to-digital signal conversion and acquisition, wifi and cellular connectivity, and power supply.
Ultrasound Sampling
Channels/Sensors per Node: 4 channel, simultaneous
Resolution: Up to 24 bits
Sampling Rate: Up to 100 kHz per sensor
Sampling Duration: Up to 300 seconds
Max Frequency Resolution: < 0.1 Hz
Peak Sensitivity: 20 – 30 kHz
Max Cable Length: 30 feet
Total Harmonic Distortion Plus Noise (THD+N): -95 dB
Electrical
Input Type: VAC
Input Voltage (AC): 85 – 264 VAC
Power (Watts): 60W
Environmental / Physical
Operating Temperature Range: 0°C to +60°C (32°F to +140°F)
Storage Humidity: 5 – 95% RH (non-condensing)
IP Rating: IP65
Data Connectivity
Connectivity: Integrated Wi-Fi 802.11a/b/g/n
LTE Cat. 1 for the US, EU, and APAC regions
WLAN Standards: 802.11a/b/g/n, Bluetooth 4.2 compliance
Frequency Band: 2.4 GHz/5 GHz
SIM Format: Nano x 2
Cellular Carrier Approvals
US: Verizon, AT&T
See how a mining and metals manufacturer leveraged Augury’s low RPM solution to uncover a critical gear issue, saving $108K.